![]() You can find more details on the available pins and labels in the PeripheralPins.c and PinNames.h files. Mass storage (USB Disk drive) for drag'n'drop programming.USB re-enumeration capability: three different interfaces supported on USB. ![]() USB VBUS or external source (3.3 V, 5 V, 7 - 12 V).The STM32 Nucleo-144 board provides an affordable and flexible way for users to try out new concepts and build prototypes with the STM32 microcontroller, choosing from the various combinations. STM32 Nucleo-32 development board with STM32F031K6 MCU, supports Arduino. STM32 Nucleo-144 development board with STM32F746ZGT6 MCU, supports Arduino, ST Zio and morpho connectivity. Selection-mode switch to use the kit as a standalone ST-LINK/V2-1 The NUCLEO-WL55JC STM32WL Nucleo-64 board, based on the MB1389 reference board.On-board ST-LINK/V2-1 debugger/programmer with SWD connector.The STM32 Nucleo-144 boards do not require any separate probe as they integrate the ST-LINK/V2-1. STMicroelectronics Morpho extension pin headers for full access to all STM32 I/Os NUCLEO-F746ZG Manufacturer PartNo : NUCLEO-F746ZG.GPIOs (168) with external interrupt capability.The code is able to run (build and upload) on the board without any problems. ARM®32-bit Cortex®-M7 + FPU + Chrom-ART™ Accelerator I’m using VS Code 1.52.1 and platformIO (core 5.0.4, home 3.3.1) with NUCLEO-F746ZG (mbed framework, upload protocol is mbed as well). The STM32 Nucleo-144 board provides an affordable and flexible way for users to try out new concepts and build prototypes by choosing from the various.The STM32 Nucleo-144 board does not require any separate probe, as it integrates the ST-LINK/V2-1 debugger/programmer and it comes with the STM32 comprehensive software HAL library, together with various packaged software examples, as well as a direct access to the ARM®mbed™online resources. The ST Zio connector, which is an extension of Arduino™ Uno, provides access to more peripherals and ST morpho headers make it easy to expand the functionality of the Nucleo open development platform with a wide choice of specialized shields. Flip are pretty straight forward, but for mode I have all those options and I'm kind of lost on which should I be using.The STM32 Nucleo-144 board provides an affordable and flexible way for users to try out new concepts and build prototypes with the STM32 microcontroller, choosing from the various combinations of performance, power consumption and features. I still have two things that I didn't get.ġ) Looking at the struct from example board file above, it's missing 3 things. I will do all the recommended tests using a scope and check timings in display datasheet, as suggested. Unless I missed something, all the pins are correctly set, including Register Select which is PD11. PalSetBusMode(&busE, PAL_MODE_ALTERNATE(12)) The NUCLEO-F746ZG is a STM32 Nucleo-144 Development Board with STM32F746ZG microcontroller provides a flexible way for users to try out new concepts and. PalSetBusMode(&busD, PAL_MODE_ALTERNATE(12)) Static const LCD_Parameters DisplayTimings = You will need to change it for your CPU and/or operating system. * This file contains a mix of hardware specific and operating system specific * GDISP Graphic Driver subsystem board interface for the SSD1963 display. * boards/addons/gdisp/board_SSD1963_fsmc.h * the license was not distributed with this file, you can obtain one at: * This file is subject to the terms of the GFX License. #define GDISP_RAM (*((volatile uint16_t *) 0圆0020000)) /* RS = 1 */Īttached is an image showing what happens. Basically, there is no image on display, only vertical lines in a white backgroud. Anyone could please explain these lines to me? I can see from where 0圆0000000 come from, but what about 0圆0020000? I don't know if the selected mode is wrong and how to change it or fi I have the FMC peripheral initialized properly. I'm trying to get this display working with my STM32F746ZG based nucleo144 board.ĭisplay is 800x480px 7" drived by SSD1963 in 16-bit 8080 parallel mode. H! I've been trying to make this work without success so if anyone could help me I would be very glad.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |